Waterproof Adhesive H0412 Surface is smooth solid and clean Waterproofing treatment at joints of diverse finishing materials
Waterproof adhesive is a waterproof coating manufactured using multiple additives. It exhibits excellent heat resistance and adapts to a wide range of temperatures.
Performance Specifications | Test Conditions | Unit | Indicator Value |
Appearance | Flowing viscous liquid | ||
Surface Drying Time | 25℃ | Min | ≤40 |
Tensile Strength | Mpa | ≥1.2 | |
Elongation at Break | % | ≥250 | |
Shear Bond Strength | Aluminum-Aluminum | Mpa | ≥1.0 |
Hardness | Shore A | ≤30 | |
Volume Resistivity | Ω.m | ≥8×1012 | |
Dielectric Loss Factor | 1MHZ | % | ≤0.5 |
Dielectric Constant | 1MHZ | 3.00±0.25 | |
Electrical Strength | Mv/m | ≥20.0 | |
Cure Degree: | 55（greater than or equal to 54.5） | ||
pH Value: | 4.0-6.5 | ||
Viscosity: | Room temperature 25 degrees Celsius: | 2700-3300MPA.S |
- Parameters
Performance Specifications | Test Conditions | Unit | Indicator Value |
Appearance | Flowing viscous liquid | ||
Surface Drying Time | 25℃ | Min | ≤40 |
Tensile Strength | Mpa | ≥1.2 | |
Elongation at Break | % | ≥250 | |
Shear Bond Strength | Aluminum-Aluminum | Mpa | ≥1.0 |
Hardness | Shore A | ≤30 | |
Volume Resistivity | Ω.m | ≥8×1012 | |
Dielectric Loss Factor | 1MHZ | % | ≤0.5 |
Dielectric Constant | 1MHZ | 3.00±0.25 | |
Electrical Strength | Mv/m | ≥20.0 | |
Cure Degree: | 55（greater than or equal to 54.5） | ||
pH Value: | 4.0-6.5 | ||
Viscosity: | Room temperature 25 degrees Celsius: | 2700-3300MPA.S |
I. Product Overview:
Waterproof adhesive is a waterproof coating manufactured using multiple additives. It exhibits excellent heat resistance and adapts to a wide range of temperatures.
Specification
Performance Specifications | Test Conditions | Unit | Indicator Value |
Appearance | Flowing viscous liquid | ||
Surface Drying Time | 25℃ | Min | ≤40 |
Tensile Strength | Mpa | ≥1.2 | |
Elongation at Break | % | ≥250 | |
Shear Bond Strength | Aluminum-Aluminum | Mpa | ≥1.0 |
Hardness | Shore A | ≤30 | |
Volume Resistivity | Ω.m | ≥8×1012 | |
Dielectric Loss Factor | 1MHZ | % | ≤0.5 |
Dielectric Constant | 1MHZ | 3.00±0.25 | |
Electrical Strength | Mv/m | ≥20.0 | |
Cure Degree: | 55（greater than or equal to 54.5） | ||
pH Value: | 4.0-6.5 | ||
Viscosity: | Room temperature 25 degrees Celsius: | 2700-3300MPA.S |
Application Method:
1. The surface must be flat, solid, clean, free of oil, dust, and other loose materials.
2. Obvious voids and pinholes must be filled and smoothed with cement mortar; sharp edges should be removed.
3. Pre-wet the substrate until no standing water remains.
4. Newly poured concrete must undergo sufficient curing time to prevent shrinkage-related issues.
5. Clean existing concrete surfaces with water, allow to dry completely before application.
IV. Product Advantages:
1. Colorless and transparent; preserves original wall finishes without yellowing or dust accumulation.
2. Resistant to heat, UV rays, ozone, acids, and alkalis with broad temperature tolerance. Modified with synthetic rubber emulsion and surfactants.
3. The coating film exhibits excellent film-forming properties, flexibility, and toughness to withstand stresses from substrate deformation and cracking.
4. Water-dispersible medium, non-flammable, odorless, environmentally friendly, and non-polluting.
5. Cold application allows easy spraying, brushing, or scraping directly onto walls.
6. The film possesses microporous breathability, suitable for heat evaporation in humid southern climates without blistering.
7. Low consumption and cost-effective (1 kg covers 4 square meters).
V. Applications:
1. Waterproofing and repair of exterior wall leaks in various buildings.
2. Waterproofing treatment at joints of diverse finishing materials.
3. Waterproofing and moisture resistance for interior/exterior wall decorative surfaces.
VI. Packaging:
50kg/drum. Securely reseal drum after each use to prevent surface drying and crusting. Store in a cool, shaded area away from direct sunlight to maintain adhesive quality.
REMARK |
The above information is believed to be accurate and presents the best explanation currently available to us. We assume no liability resulting from above content. The technical standards are formulated and revised by customers’ requirement and us, if there are any changes, the latest specification will be executed and confirmed in the contract. |
Previous : Water-Based Yellow Glue 930# H0411 Textile Industry Non-woven fabrics textiles
Next : PP glue H0413 clean and dry the surface of the adhesive material Finger jointing can also be used for post-forming processing of office furniture
Copy product links
Long by picture save/share
Waterproof Adhesive H0412 Surface is smooth solid and clean Waterproofing treatment at joints of diverse finishing materials
INQUIRY
Add Successfully
At vero eos et accusamus et iusto elity agnissmos ducimus os quidtiis praesetium ptatum mole deeniti .
GET IN TOUCH
Address: M18-101, chemical zone, China south city, , shenzhen city, guangdong province, China.
Tell : (+86) 755-88834518
(Monday to Friday: 9:00-18:00)
Email : tanya@jitian168.com
Email : resin@jitian168.com
BUSINESS HOURS
Monday to Friday : 9 am to 6 pm
Saturday : 10 am to 4 pm
Sunday : Closed Support Hours in 24/7 Everyday
NEWS LETTER
Enter your email address for our mailing list to keep your self our lastest updated.
点击右上角
分享给朋友吧
© 2022 SHENZHEN JITIAN CHEMICAL CO.,LTD . All rights reserved Site Map
